Winchester-repeating-arms 9422 (Historic Manual) Instrukcja Użytkownika

LicenseeWinchester Model 9422 & Model 9417 Rimfire Lever Action Rifle Owner’s Manual02-228-WFA_M9417/22 OM 7/16/03 1:58 PM Page 27

10NEVER USE ANY AMMUNITION IN A 9422 OR9417 THAT IS NOT SPECIFICALLY INDICATEDON THE BARREL.AMMUNITION — MODEL 9417The caliber of your Model 9417 is i

11U.S. Repeating Arms Co. can assume no responsibility for incidents which occur through use of cartridges of nonstandard dimension or those developin

12FIGURE 4Loosen the takedownscrew carefully.Remove the bolt slide and breech bolt together.FIGURE 6Breech boltBolt slideReceiverFIGURE 7FIGURE 5Separ

133. Pull the hammer back to full-cock position and closefinger lever.4. Slide the frame into the receiver from the rear (Figure 11). 5. Insert and ti

14Make sure the breech boltand bolt slide fit into the railsin the receiver.FIGURE 10Slide the two halves together. (Shown with gun laying on table.)

15firmly hold the hammer back with your thumb. While holding the hammer, apply just enough pressure on the trigger to release the hammer from the ful

16Twist the magazine tube plug to unlock and pull the tubeout until the colored follower clears the loading port inthe outer magazine tube. With the

17TO UNLOAD THE MAGAZINEAND CHAMBERPlace the hammer in the safety (half-cock) position.With the rifle pointed upward, withdraw the inside magazine tub

18• Move the blade and holder up to shoot higher.• Move the blade and holder down to shoot lower.For finer elevation adjustments the sight blade itsel

19Care should be taken not to mar the finish, damage the attaching screws or bend sight components whenadjustments are made.The front sight bead is al

2Important instructions for Winchester Model 9422 & Model 9417 Lever Action RifleU. S. Repeating Arms Company, Inc.275 Winchester AvenueNew Haven,

20MOUNTING A SCOPEThe top of the receiver on every Model 9422 and Model9417 is grooved to accept standard 22 caliber rifle-typescope mounts. Depending

21If you have trouble starting the screw into the threads itmay be because of the thread locking compound on thescrew itself. This thread locking comp

227. Tighten the set screw, making sure it engages into theindent made by the center punch.WARNING: HAMMER EXTENSIONS CANLOOSEN WITH USE. OCCASIONALLY

23with solvent. If or when fouling should become heavy, itcan be removed with a brass bore brush. Dip or spray thebrush with solvent and scrub the cha

NEVER ATTEMPT TO TAKE YOUR MODEL9422 OR MODEL 9417 APART FURTHER THANEXPLAINED IN THIS MANUAL.This is a specialized, finely fitted mechanism. You mayp

You Are Responsible For Firearms Safety As a gun owner, you accept a set of demanding responsibilities. How seriously you take these responsibilities

6. BEWARE OF BARREL OBSTRUCTIONS, for the safety of both your gun and yourself. Mud, snow, and an infinite variety of other obstructions may inadvert

11. BE SURE OF YOUR TARGET AND BACKSTOP. Particularly during low light periods. Know the range of your ammunition. Never shoot at water or hard object

20. READ AND HEED ALL WARNINGS in this instruction book, on ammunition boxes and with all accessories that you install on your firearm. It is your res

U.S. Repeating Arms Company, Inc.275 Winchester AvenueMorgan, Utah, U. S. A. 84050-9333www.winchester-guns.comLicenseeWinchester trademarks licensed

3Contents PageGun safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Features . . . . . . . . . . . . . . . . . . . . . . . .

4GUN SAFETY WARNINGSIT IS ESSENTIAL THAT THESE OPERATINGINSTRUCTIONS BE THOROUGHLY STUDIEDBEFORE USING THIS FIREARM TO ASSUREPROPER AND SAFE GUN HANDL

57. Before firing, clean any grease or oil out of barrel withcleaning rod and patch. Grease or heavy accumulation ofoil can cause excessive pressure a

6Conventional lever action designwith three-position hammer.All-steel receiver and steel components. Every componentof the internal firing mechanismis

7The quick take-down feature allows you to easily disassemble yourModel 9422 or Model 9417 into two halves. A single screw on the left sideof the rece

8GENERAL DESCRIPTIONYour new Model 9422 or Model 9417 is one of several different versions and configurations offered. The basicoperating procedures a

The Winchester Model 9422 and Model 9417 are alsoshown disassembled to the extent necessary in order tofollow instructions contained in this book (Fig