Winchester-repeating-arms 9410 Top Tang Safety (Historic Manual) Instrukcja Użytkownika

LicenseeWinchester Model 9410 Lever Action Shotgun Owner’s Manual — Top-Tang Safety Version02-224-WFA_9410_OM_revis 7/16/03 2:52 PM Page 41

All models are drilled and tapped for scope mounts. With a scopeand the proper rifled slug your Model 9410 can be effective forvarmints and game — wit

11The Model 9410 features a specially designed ejector/extractor system that does not eject the shell until the lever is worked fullyforward. This giv

12• Never attempt to load 3" shells.• Barrel has a smooth bore with no rifling.• Designed to shoot all factory21⁄2" field and target loads.2

13Incorrectly reloaded ammunition can cause serious personal injury and damage to the firearm due to excessivepressure. Reload only after proper instr

is prevented from moving forward and striking the firingpin. The rebound position and the manual hammerstop/safety are intended to work together to pr

15position when the trigger is pulled. When the trigger ispulled — with the safety on — the hammer drops, goingimmediately to the rebound position wit

16imminent, it is important to lower the hammerimmediately to the rebound position from the cockedposition. To do this: 1. Make sure the barrel is poi

17from depressing the trigger stop — making it necessary tosqueeze upward on the finger lever.Remember, never rely totally on your firearm’smechanical

18hammer will fall and strike the firing pin. If a cartridge isin the chamber, the firing pin will strike the primer andfire the cartridge. To place t

19in some situations you may want the advantage of a scopeor dot type sight. Scope mounts are available separately.General instructions for installing

2Important instructions for Winchester Model 9410 Lever Action .410 ShotgunWith Top-Tang SafetyCustomer Service Department (United States)U. S. Repeat

20difficult to close the action. Make sure all surfaces areclean if any unusual resistance is felt. However, rememberthat this is a finely fitted acti

21Be sure to check the shell to make sure it is a 21⁄2" shelland not a 3" shell. If it is a 3" shell do not use it or try tochamber it

22directly into the chamber with the magazine alreadyloaded it may be difficult or impossible to close theaction. You may need to remove the shell fr

23BY LOOKING THROUGH THE TOP OF THEOPEN RECEIVER, THAT THE MAGAZINE FOLLOWER IS SHOWING—AND NOT A SHELL BASE. ALWAYS DOUBLE CHECK THAT NO SHELLS REMAI

24This is not a procedure you want to do often — so pleasebe very careful not to mix 21⁄2" and 3" shells in your pockets. The Model 9410 is

FIRING PROCEDURESIMPORTANT: WHEN YOU ARE PREPARING TOSHOOT, IT IS ALWAYS ESSENTIAL THAT YOUBE TOTALLY SURE OF YOUR TARGET.ALWAYS BE AWARE OF ALL OBJEC

3. WHEN THROUGH FIRING ALWAYSIMMEDIATELY PLACE THE TOP-TANG SAFETYIN THE “ON” POSITION (FIGURE 19), AND THEHAMMER IN THE SAFETY (REBOUND)POSITION (FIG

the sights set as they come from the factory (intermediateposition on both elevation and windage), and then makeincremental adjustments to move the si

Care should be taken not to mar the finish, damage the attaching screws or bend sight components whenadjustments are made.All sight adjustments are a

STANDARDINVECTOR™ THREADED CHOKE TUBE SYSTEMSome Model 9410s are fitted with the interchangeableStandard Invector™ choke tube system. If your shotgunh

3LicenseeContents PageGun Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . .5Gene

303. Use the Standard Invector wrench to loosen the tube,turning it counterclockwise. Finger twist the tube the restof the way out of the barrel.TUBE

SPECIAL CARE OF CHOKE TUBESAND CHOKE TUBE THREADS— 1. If your gun is equipped with Standard Invector choketubes, do not use a brass brush to clean you

32The hammer extension can be used in either the righthand or left hand position. To install, coat the hammerextension threads with Loctite®thread loc

33MAGAZINE PLUGThe 9410 is delivered with a three-shot adapter plugincluded in the box. This plug limits magazine capacity totwo shells in compliance

6. Replace the magazine end cap, pushing the spring backdown into the magazine tube.7. Replace the magazine cap retaining screw.ADAPTER INSTALLATION M

post mounting stud, note the two different sized holes inthe end of the magazine tube (Figure 31). The larger holemust face away from the barrel.8. Re

3610. Return forearm cap to original location and secureforearm cap with screws.CLEANING ANDMAINTENANCE SUGGESTIONSThe Model 9410 will function better

37breaking off, the brush should be pushed completelythrough the bore before being withdrawn. If cast leadslugs are used a lead solvent may be used as

38This is a specialized, finely fitted mechanism. You maypermanently mar it by attempting to disassemble theinner mechanism assemblies. If further dis

39WINCHESTERGUNS.COMU.S. Repeating Arms Company offers an informationresource for you on the world wide web.• List of authorized repair centers.• Cust

4THANK YOUWe sincerely hope that you are pleased with your new Winchester 9410 shotgun.We at U.S. Repeating Arms Company thank you for the privilege o

You Are Responsible For Firearms Safety. As a gun owner, you accept a set of demanding responsibilities. How seriously you take these responsibilitie

7. BEWARE OF BARREL OBSTRUCTION. Do this for the safety of both your gun and yourself. Mud, snow, and an infinite variety of other objects may inadve

12. USE SHELLS OF CORRECT LENGTH. The size of the chamber is inscribed, along with gauge and choke designations, on the side of the barrel. Do not

22. SUPERVISE AND TEACH FIREARMS SAFETY TO ALL MEMBERS OF YOUR FAMILY -- ESPECIALLY TO CHILDREN AND NONSHOOTERS. Closely supervise newcomers to the s

U.S. Repeating Arms Company, Inc.275 Winchester AvenueMorgan, Utah, U. S. A. 84050-9333www.winchesterguns.comLicenseeWinchester trademarks licensed f

5GUN SAFETY WARNINGSIT IS ESSENTIAL THAT THESE OPERATINGINSTRUCTIONS BE THOROUGHLY STUDIEDBEFORE USING THIS FIREARM TO ASSUREPROPER AND SAFE GUN HANDL

68. Keep barrel, chamber and action free of rust. Rust inthe barrel and chamber can cause excessive pressuresresulting in serious injury. A rusted, pi

7GENERAL DESCRIPTIONCongratulations on your purchase of a Winchester Model 9410 shotgun — certainly one of the most uniqueand fun-to-shoot guns ever.

8All features are explained in detail later in this manual.Some versions may vary slightly in appearance, but basicoperation and function remain the s

9FAMILIAR WITH ALL PART NAMES LISTEDBEFORE PROCEEDING WITH THE REST OFTHE INSTRUCTIONS IN THIS MANUAL.SERIAL NUMBERThe serial number is located on the